NeuroTrac MyoPlus EMG & EMS PRO

The new user-friendly touch screen-based interface makes it a self-explanatory unit with interactive learning on the go, including electrode placement, running EMG graph, EMG biofeedback Games and Templates as well as many other helpful tools.

• Pre-set programmes for Incontinence treatment (including a special programme for the treatment of incontinence by stimulating the nervous tibialis posterior with self-adhesive electrodes) and neuro-muscular Rehabilitation.
• Supplied with Rubber sleeve with stand and lanyard attachment option.
• Designed for Physiotherapist in mind to be used as a portable tool. Suitable as a personal trainer for in-clinic or home use (under guidance).
• Single channel EMG (Biofeedback) combined with 1 channel of NMES (stimulation).
• Single channel ETS (EMG triggered stimulation) with single channel stimulation.
• Simple single-phase or multiphase operation: multiphase allows EMG/ETS/STIM to be combined in one programme.
• Multilingual full colour display screen and voice prompts for Biofeedback.
• Manual and Automatic threshold control.
• EMG Biofeedback between stimulation (muscle activity and tiredness indication when using muscle stimulation).
• Standalone device or used in conjunction with established multilingual software.
• Up to 10 meters of wireless (Bluetooth) connection for NeuroTrac Software.
• For home users: Produces and prints (with the optional PC Software) the comprehensive patient progress reports on a day-to-day basis providing average readings on work/rest, peak, onset and muscle release times, work and rest deviations and the average mA current.
• Used as a learning tool for both patient and clinician with emphasis on improving treatment techniques in the use of EMG and Neuromuscular stimulation.

1. 1. EMG
   1. Single channel EMG
   2. EMG Range: 0.2 to 2000 μV RMS (continuous)
   3. Sensitivity: 0.l μV RMS
   4. Accuracy: 4% of μV reading +/-0.3 μV at 200 Hz
   5. Selectable Bandpass filter – 3db Bandwidth,
      1. a. Wide: 18 Hz +/- 4 Hz to 370 Hz +/- 10% – Reading below 235 microvolts 10 Hz +/-3 Hz to 370 Hz +/- 10% – Reading above 235 microvolts
      2. b. Narrow: 100 Hz +/- 5% to 370 Hz +/- 10%
   6. Notch filter: 50 Hz (Canada 60Hz) – 33 dbs (0. 1% accuracy)
   7. Common Mode Rejection Ratio: 130 dbs Minimum @ 50 Hz
   8. Work / Rest periods: 2-99 seconds
   9. Number of Trials: 2-99

1. NMES, TENS and ETS

1. Single channel Stimulator
2. Amplitude: 0-90 mA into 500 Ohm load – actual mA will tend to be less than indicated due to Electrode impedance: at 1000 Ohms load (Electrodes in poor condition) the maximum will be limited to 86 mA, at 1500 Ohms load the maximum will be limited to 65 mA.
3. Type: Constant current, maximum output voltage 180 Volts +10 / -30 Volts
4. Waveform: Symmetrical, rectangular, bi-phasic with net zero DC current
5. Pulse width selection: 50-450 μS in predefined, 50-330μS in custom (10% accuracy)
6. Pulse rate selection: 2-100 Hz (5% accuracy)
7. Work / Rest periods: 2-99 seconds
8. Time 1 – 99 minutes
9. Ramp up time: 0.1 – 9.9 seconds
10. Preset and user programmable treatment Programs
11. Automatic output shut off with detection of open electrode above 10 mA (+/- 2mA).

Battery:
Battery set: 4 x 1.5V, AAA battery.
Low battery indication at 4.2-4.4 volts +/- 0.2 volts, automatic shut off when voltage drops below the low indication. Replace the batteries immediately!
The device goes off automatically when not in use (energy saving): for example when in settings and no key is pressed over 1 minute when in stimulation mode (home screen) and all channels are 0mA.

Expected average battery set life [of standard 850 mAh, alkaline]:
14-18 hours in STIM, 28 hours in EMG mode.

Environmental Conditions for use:
+5 to +40 degrees Centigrade. 15-90% Humidity.

Environmental conditions for storage & transport:
-25 to +70 degrees Centigrade. 15-90% Humidity.

Physical:
Dimensions: Length 150mm, Width 89mm, Depth 35mm
Weight: 140g (without batteries)